تعداد ۵ دستگاه سرور HP ProLiant DL320e Generation 8 کارکرده و دست دوم ولی با ظاهر بسیار تمیز به همراه دو عدد هارد دو ترابایت و دو عدد رم ۴ گیگابایتی به همراه ریل با قیمت بسیار نازل به فروش می رسد . لازم به ذکر است ارزش خرید این کالا با توجه با کارکرد ، قیمت و همچنین مشخصات فنی بسیار بالا می باشد .
NOTE: For the Standard Features shipped in the “Factory Integrated Models”, please see the “Configuration Information – Factory Integrated Models” section.
Processor One of the following depending on Model
Entry Processors
Intel® Pentium® G2120 (3.1GHz/2-core/3MB/55W) Processor NOTE: Intel® Pentium® G2120 Processor supports up to 1600MHz DDR3 memory speeds.
Intel® Pentium® G2100T (2.6GHz/2-core/3MB/35W) Processor NOTE: Intel® Pentium® G2100T Processor supports up to 1600MHz DDR3 memory speeds.
Base Processors NOTE: All support up to1600MHz DDR3 memory speeds.
NOTE: HT indicates that the processor model supports Intel® /Hyper-Threading Technology (Depends on the processor). NOTE: DDR3 speed is the maximum memory speed of the processor. Actual memory speed may depend on the quantity and type of DIMMs and CPU installed (options for 1600, 1333, 1066MHz).
Cache Memory One of the following depending on Model
۸MB (1x8MB) Level 3 NOTE: For Quad-core processors.
۳MB (1x3MB) Level 3 NOTE: For Dual-core processors.
NOTE: HP memory from previous generation servers are not fully compatible with the HP ProLiant DL320e Gen8 Server. NOTE: To realize the performance memory capabilities listed in this document, HP SmartMemory is required. For additional information, please see the HP SmartMemory QuickSpecs at:http://h18000.www1.hp.com/products/quickspecs/14225_div/14225_div.html NOTE: Depending on the memory configuration and processor model, the memory speed may run at 1600MHz, 1333MHz, or 1066MHz. Please see Memory Population Table or the Online Memory Configuration Tool at: www.hp.com/go/ddr3memory-configurator.
Network Controller
HP Ethernet 1Gb 2-port 330i Adapter NOTE: The HP ProLiant DL320e Gen8 server has an embedded dual-port network adapter . The server can be further upgraded with various networking products
Expansion Slots
Expansion
Slots #
Technology
Bus
Width *
Connector Width
Form Factor
Notes
۱
PCIe 2.0
x4
x8
Low profile slot
۲
PCIe 3.0
x16
x16
Half-length, full-height slot
*Indicates the number of physical electrical lanes running to the connector. NOTE: PCIe 3.0 support with Intel Xeon E3-1200v2 family only.
HP Server ROM
HP ROM (Read Only Memory) is now digitally signed using HP’s Corporate Signing Service. This signature is verified before the flash process starts, reducing accidental programming and preventing malicious efforts to corrupt system ROM.
HP ROM provides for essential initialization and validation of hardware components before control is passed to the customer-installed operating system. The ROM also provides the capability of booting from various fixed media (HDD, CD-ROM) and removable media (USB), to continue operation to the operating system.
HP ROM performs very early configuration of the video controller, to allow monitoring of initialization progress via an attached monitor. If configuration or hardware errors are discovered during this early phase of hardware initialization, suitable messages are now displayed on the connected monitor. Additionally, these configuration or hardware errors are logged to the Integrated Management Log (IML) to assist in diagnosis.
HP’s ProLiant ROM is used to configure the following:
Processor and chipset status registers
System memory, memory map, and memory initialization
System hardware configuration (Integrated PCI devices and optional PCIe cards).
Customer-specific BIOS configuration (using the HP ROM-Based Setup Utility (RBSU).
NOTE: For further information, please refer to HP’s RBSU (ROM based setup utility) user guide:www.hp.com/support/rbsu.
Storage Controller One of the following depending on Model
Entry Models
(Non hot plug)
HP Dynamic Smart Array B120i Controller NOTE: Supports 3.0Gb/s SATA. NOTE: Supports RAID 0/1/10 only. It does not have FBWC support so cannot support advanced RAID (5 onwards). For FBWC, a standup Smart Array Controller card must be configured.
Base Models
(Hot plug)
HP Dynamic Smart Array B120i Controller NOTE: Supports 3.0Gb/s SATA. NOTE: Supports RAID 0/1/10 only. It does not have FBWC support so cannot support advanced RAID (5 onwards). For FBWC, a standup Smart Array Controller card must be configured.
Performance Models
(Hot plug)
HP Smart Array P222/512MB FBWC controller NOTE: P222 can support RAID 0/1/10/5/5+0/6/6+0. NOTE: HP Smart Array Advanced Pack (SAAP 2.0) is no longer required to enable RAID 6 & 60 (Advanced Data Guarding). However, controller must be in firmware version 4.68 (or later).
NOTE: The DL320e Gen8 can support other advanced controllers as well, depending on model and configuration NOTE: For set up instructions for HP Smart Array B120i SATA Controller please refer to the HP ProLiant DL300 series server user guide. NOTE: For general information about HP Smart Array B120i SATA RAID Controller, please visit: http://h18004.www1.hp.com/products/servers/proliantstorage/arraycontrollers
/dynamicsmartarray/index.html
Internal Storage Devices
Diskette Drive
None
Optical Drive
Optional
DVD-ROM, DVD-RW
Hard Drives One of the following depending on Model
None ship standard (Base Models and Performance Models)
۱x NHP 500GB SATA 3.5″ drive (Entry Models)
Hard Drive Bays
۸ SFF drive bays or 4 LFF Non hot plug/Hot plug
NOTE: HP ProLiant DL320e Series servers offer both SFF, and LFF versions in CTO. The Optical Drive bay is available with both models. NOTE: LFF versions are not an upgradeable option from SFF models, or vice versa, also between Non Hot Plug LFF and Hot Plug LFF. NOTE: All Pre-configured Models come populated with some hard drive blanks installed. Should the customer need additional hard drive blanks, they can order more using either P/N 666987-B21: HP SFF Gen8 Hard Drive Blank Kit or P/N 666986-B21: HP LFF Gen8 Hard Drive Blank Kit. These part numbers for single HDD blanks below are also provided should the customer require replacement HDD blanks for their server.
Maximum Internal Storage
Hot Plug SFF SAS
۹٫۶TB
۸ x 1.2TB
Hot Plug SFF SATA
۸٫۰TB
۸ x 1TB
Hot Plug LFF SAS
۱۶٫۰TB
۴ x 4TB
Hot Plug LFF SATA
۱۶٫۰TB
۴ x 4TB
Hot Plug SFF SAS SSD
۶٫۴TB
۸ x 800GB
Hot Plug SFF SATA SSD
۶٫۴TB
۸ x 800GB
Hot Plug LFF SATA SSD
۳٫۲TB
۴ x 800GB
Non-Hot Plug LFF SATA
۱۲٫۰ TB
۴ x 3TB
Interfaces
Serial
۱
Video
۱ Rear standard video
HP iLO Remote Management Network Port
۱Gb Dedicated
SD slot
۱ Internal NOTE: The SD slot is not a hot-pluggable device. Customers should not attempt to plug an SD card into the SD slot while the server is powered.
USB 2.0 Ports
۷ total: 4 rear, 2 front, 1 internal (Optional)
Industry Standard Compliance
ACPI 2.0b Compliant
PCIe 3.0
PXE Support
WOL Support
USB 2.0 Compliant
Server Power Cords
All Pre-configured Models servers ship with a high voltage server to PDU power cord. NOTE: HP ProLiant DL servers no longer ship standard with a 12-foot NEMA 5-15P to C13 power cords (227099-001) that allow connection to 110V US wall outlets in a home or office. ProLiant DL servers are primarily connected to PDU’s in data center racks so they now ship standard with only a PDU 6-foot C-14 to C13 power cord (142258-001). If a user wishes to power a ProLiant DL server using a110V receptacle (NEMA-15), the 12-foot NEMA 5-15 to C13 power cord must be ordered separately. See Power Cords section for Worldwide Power Cord options.
NOTE: The default power supply for DL320e Gen8 server is a 350W Non Hot Plug, Non Redundant (ATX) power supply with 85% efficiency. NOTE: To choose a Redundant Common Slot Power Supply option for the DL320e Gen8 server, a Factory Integrated Model must be chosen, beginning with a CTO server. Also, an HP DL320e Gen8 RPS Enablement FIO Kit (675451-B21) is required.
HP’s Common Slot (CS) power supplies allow for commonality of power supplies across a wide range of ProLiant and Integrity servers, as well as HP Storage solutions, and are designed to provide the highest power supply efficiency without degrading system performance. HP CS power supplies are tested by the Electric Power Research Institute (EPRI) and certified through the ECOS 80 Plus power supply program. The 460W HP CS power supply option provides an efficiency rating of up to 94%. All HP Common Slot power sources are UL, CE Mark Compliant, hot-plug and support redundant configurations.
NOTE: Mixing of power supplies (for instance Common Slot Platinum Plus power supplies and Common Slot Gold power supplies) in the same server is not supported. All power supplies must be of the same output and efficiency rating. If non-matched power supplies are inserted you will get errors and operation will fail.
HP CS Platinum Plus power supplies are required when enabling HP’s Intelligent Power Discovery (IPD) solution. IPD is the first technology to create an automated, energy-aware network between IT systems and facilities. This allows your company to reclaim millions of dollars in wasted power capacity and downtime costs across data centers. For more information on HP’s IPD solution, go to www.hp.com/go/ipd.
It is highly recommended that you use the HP Power Advisor in defining the “Right-Size” power supply for your needs. HP Power Advisor can be accessed at: www.hp.com/go/hppoweradvisor.
NOTE: The 80 PLUS program is a unique forum that unites electric utilities, the computer industry, and consumers in an effort to bring energy efficient technology solutions to the marketplace. 80 Plus independently tests power supply efficiency and publicly posts the results on 80Plus.org.
Redundant Power: Optional (1+1 or n+n redundant) power supplies can be purchased through power supply option kits (see Power Supplies for part numbers).
NOTE: For more information on HP’s Certified and Supported ProLiant Servers for OS and Virtualization Software and latest listing of software drivers available for your server including how to purchase from HP, please visit our OS Support Site at: http://www.hp.com/go/ossupport and our driver download page:http://www.hp.com/support/DL320eGen8.
Graphics
Integrated Matrox G200 video standard
۱۲۸۰ x 1024 (32 bpp)
۱۹۲۰ x 1200 (16 bpp)
HP iLO 4 On System Management Memory
۱۶ MB Flash
۲۵۶ MB DDR 3 with ECC (112 MB after ECC and video)
Form Factor One of the following depending on Model
۱U Rack form factor
۸ SFF Drive Bay Version:
۱٫۷″ (۴٫۳۲cm) Height x 17.11″ (43.46cm) Width x 27.5″ (69.90cm) Length
۴ LFF Drive Bay Version:
۱٫۷″ (۴٫۳۲cm) Height x 17.11″ (43.46cm) Width x 29.5″ (75.00cm) Length
On System Management
HP iLO Management Engine
HP iLO Management Engine is a comprehensive set of embedded management features supporting the complete lifecycle of the server, from initial deployment, through ongoing management, to service alerting and remote support. HP iLO Management Engine comes standard on all HP ProLiant Gen8 servers. The HP iLO Management Engine portfolio includes:
HP iLO: The HP iLO (Integrated Lights-Out) management processor is the core foundation for the HP iLO Management Engine
HP Agentless Management: Provides built in server health monitoring and alerting capability without OS agents, that starts working the moment a power cord and an Ethernet cable are connected.
HP Active Health System: Always on, continuous monitoring for increased stability and shorter downtimes; 100% configuration history; Health and service alerts and easy export and upload to Service and Support.
HP Intelligent Provisioning: Lets customers provision and configure a single server without any separate media. No more SmartStart CDs or Smart Update Firmware DVD are needed.
To start Intelligent Provisioning:
Press the F10 key during the ProLiant Gen8 server boot process (also known as power on self test or POST).
Use the Service Pack for ProLiant (SPP) atwww.hp.com/go/spp to get firmware and software updates.
HP iLO Mobile App: Enables the ability to access, deploy, and manage your server anytime from anywhere from select smartphones and mobile devices. For additional information please visit: www.hp.com/go/ilo/mobileapp
NOTE: For more information, visit: http://www.hp.com/go/ilo or HP iLO Management Engine technologies whitepaper
HP Insight Management
HP Service Pack for ProLiant
HP Service Pack for ProLiant (SPP) and HP Smart Update Manager (HP SUM) provide a comprehensive approach to firmware and system software maintenance. Together they provide better operating stability and ensure maximum uptime. The SPP will be updated at a predictable cadence, typically coinciding with new HP server hardware launches. By enabling firmware to be updated online and integrating firmware and system software updates in one operation, HP SUM and the SPP offer faster updates of individual servers and dramatically faster updates of entire BladeSystem enclosures. Further improving system uptime and stability is the fact that HP provides 12 months of support for each Service Pack for ProLiant release.
The user experience around HP SUM and the SPP has been improved in several ways, starting with the web download. A single web page provides access to a single download containing both the latest version of HP SUM and the latest SPP. Optional smaller subsets with only specific types of servers or specific operating systems are offered to save on download time. The HP SUM application provides a straightforward, intuitive user interface that guides the user through the steps of discovery, analyses and update, providing comprehensive information on available updates, criticality and interdependencies. This information is also available in reports. By providing the option of multiple local or shared repositories which can be easily updated from hp.com, HP SUM provides the tools to optimize stability and consistency throughout the company. While HP SUM and the SPP recommend the combinations of firmware and system software that HP has found to be the best practice, the application gives customers the flexibility to set their own specific baseline.
The Service Pack for ProLiant has been rigorously tested with specific attention for interaction between firmware, drivers and agents both within the server as well as in interaction with the BladeSystem enclosure components (Onboard Administrator and Virtual Connect). This testing ensures the highest quality as well as providing the input for HP SUM to deploy updates taking into account all interdepencies, when determining the correct updates and order of update deployment.
This product is covered by a global limited warranty and supported by HP Services and a worldwide network of HP Authorized Channel Partners resellers. Hardware diagnostic support and repair is available for three years from date of purchase. Support for software and initial setup is available for 90 days from date of purchase. Enhancements to warranty services are available through HP Care Pack services or customized service agreements. Hard drives have either a one year or three year warranty; refer to the specific hard drive QuickSpecs for details. NOTE: Server Warranty includes 1-Year Parts, 1-Year Labor, 1-Year Onsite support with next business day response. Warranty repairs may be accomplished through the use of Customer Self Repair (CSR) parts. These parts fall into two categories: 1) Mandatory CSR parts are designed for easy replacement. A travel and labor charge will result when customers decline to replace a Mandatory CSR part; 2) Optional CSR parts are also designed for easy replacement but may involve added complexity. Customers may choose to have HP replace Optional CSR parts at no charge. Additional information regarding worldwide limited warranty and technical support is available at:http://h18004.www1.hp.com/products/servers/platforms/warranty/index.html
HP Insight Control, a product option, delivers essential infrastructure management that can help save time and money by making it easy to deploy, migrate, monitor, remote control, and optimize your IT infrastructure through a single, simple management console. HP Insight Control also supports Location and Power Discovery Services to automate many configuration, asset tracking, and power management tasks to speed implementation and prevent downtime. For more information, see http://www.hp.com/go/insightcontrol.
HP Insight Control includes one year of 24 x 7 HP Software Technical Support and Update Service ensuring rapid access to HP support staff and proactive delivery of software updates. For more information about this service, see:http://www.hp.com/services/insight.
HP iLO Essentials
HP iLO Essentials license ideal for small and medium business customers. The specially created HP iLO Essentials (a subset of iLO Advanced functionality) saves SMB customers time and money, by ease of remote server set up through the interactive virtual media, lowering operational costs with remote access via the Integrated Remote Console, and faster time to resolution with email-based proactive notifications. With this newly designed HP iLO Essentials license SMB customers now have the option of a server management package solely design and priced just right for their IT environments. HP iLO Essentials is available on all HP ProLiant Gen8 e-series making this an ideal solution for small business owners. For more information, see: http://www.hp.com/go/iLO/essentials
HP iLO Advanced
HP Integrated Lights-Out Advanced License a product option, providing smart remote server management without compromise. iLO Advanced unlocks the full set of remote administration functionality for all HP ProLiant servers by activating the full Virtual Keyboard Video and Mouse remote console, multi-user collaboration, console record and replay, GUI-based and scripted virtual media and virtual folders, and enhanced security and power management functionality. For more information, see: http://www.hp.com/go/iloadvance
HP Matrix Operating Environment
The HP Matrix Operating Environment (Matrix OE) for ProLiant and Integrity servers is an integrated command center that helps you instantly adjust to dynamic business demands. This advanced infrastructure management software lets you reduce the cost of common data center tasks by up to 40 percent while keeping pace with your changing business.
The HP Matrix OE includes the automated provisioning, optimization, and recovery management capabilities for HP CloudSystem Matrix, the ideal platform for private cloud and Infrastructure as a Service (IaaS).
HP Cluster Platforms are specifically engineered, factory-integrated large-scale ProLiant clusters optimized for High Performance Computing, with a choice of servers, networks and software. Operating system options include specially priced offerings for Red Hat Enterprise Linux and SUSE Linux Enterprise Server, as well as Microsoft Windows HPC Server. A Cluster Platform Configurator simplifies ordering.http://www.hp.com/go/clusters.
HP HPC Interconnects
High Performance Computing (HPC) interconnect technologies are available for this server as part of the HP Cluster Platform portfolio. These high-speed InfiniBand and Gigabit interconnects are fully supported by HP when integrated within an HP cluster. Flexible, validated solutions can be defined with the help of configuration tools. http://www.hp.com/techservers/clusters/ucp/index.html
HP Insight Cluster Management Utility
HP Insight Cluster Management Utility (CMU) is an HP-licensed and HP-supported suite of tools that are used for lifecycle management of hyperscale clusters of Linux ProLiant systems. CMU includes software for the centralized provisioning, management and monitoring of nodes. CMU makes the administration of clusters user friendly, efficient, and effective. http://www.hp.com/go/cmu
Storage Software
Whether you need to solve a specific data protection, archiving, or storage command and control challenge, or deliver on strategic consolidation, compliance, or continuity initiatives, look no further than HP storage software. Our storage software helps you reduce costs, simplify storage infrastructure, protect vital assets and respond faster to business opportunities.
Storage software that gets the job done:
Data Protection and Recovery Software
Whether you’re a large enterprise or a smaller business, HP data protection and recovery software will cost-effectively protect you against disaster and ensure business continuity.
Data Archive and Migration Software
HP’s storage software enables you to comply with data retention and retrieval requirements, improve application performance, and reduce costs by efficiently migrating infrequently accessed or less valuable data to lower cost storage.
Storage Resource Management Software (SRM)
HP’s storage resource management software reduces operational costs and provides the command and control foundation you need to efficiently manage and visualize your physical and virtual environments.
Data Replication Software
HP offers array-based and host-based replication software for use in disaster recovery, testing, application development and reporting.
Storage Device Management Software
Maximize your investment in HP storage and networking with software that enables hardware-specific configuration, performance tuning and connectivity management.
HP StoreVirtual VSA
With HP StoreVirtual VSA you can use the power of virtualization to turn a set of heterogeneous and disconnected physical disk drives in your servers and storage devices into a single pool of logical storage capacity.
HP Insight Online is a new addition to the HP Support Center for one stop, secure access to product and HP support information personalized to your IT environment. Insight Online can automatically display devices remotely monitored by HP Insight Remote Support. With Insight Online’s easy navigation you can efficiently track your IT support contracts and device status from anywhere and at anytime. www.hp.com/go/insightonline
HP Proactive Insight experience
Prevent problems with innovative, automated monitoring tools and proactive services. The HP Proactive Insight experience consist of using Insight Online, Insight Remote Support, and Proactive Care Support Service as one integrated solution. The Proactive Insight experience provides you with expert advice and personalized, cloud-based automated IT support, helping to prevent unplanned down time and solve problems quickly. For more information, visit: www.hp.com/go/proactiveinsightexperience
Factory Express Portfolio for Servers and Storage
HP Factory Express offers configuration, customization, integration and deployment services for HP servers and storage products. Customers can choose how their factory solutions are built, tested, integrated, shipped and deployed.
Factory Express offers service packages for simple configuration, racking, installation, complex configuration and design services as well as individual factory services, such as image loading, asset tagging, and custom packaging. HP products supported through Factory Express include a wide array of servers and storage: HP Integrity, HP ProLiant, HP ProLiant Server Blades, HP BladeSystem, HP 9000 servers as well as the MSAxxxx, VA7xxx, EVA, XP, rackable tape libraries and configurable network switches.
For more information on Factory Express services for your specific server model please contact your sales representative or go to: http://www.hp.com/go/factory-express.
HP Simple Configurator
SCE is a guided self service tool to help sales and non technical people provide customers with initial configurations in 3 to 5 minutes. You may then send the configuration on for configuration help, or use in your existing ordering processes. If you require “custom” rack configuration or configuration for products not available in SCE, please contact HP’s Customer Business Center or an Authorized Partner for assistance.http://www.hp.com/products/configurator
HP Technology Services for Industry Standard Servers and BladeSystem
Capitalizing on HP ProLiant server and HP BladeSystem capabilities requires a service partner who understands your increasingly complex business technology environment. That’s why it makes sense to team up with the people who know HP infrastructure hardware and software best – the experienced professionals at HP Services.What HP ProLiant and BladeSystem Services can do for you
HP ProLiant and BladeSystem Services can help you design, deploy, test, integrate, support, and manage IT and infrastructure solutions. This way, HP proposes services solutions that include more than just uplift of base warranty. Foundation Care services deliver scalable support-packages for HP industry-standard servers and software. You can choose the type and level of service that is most suitable for their business needs. New to this portfolio is HP Collaborative Support. If you are running business critical environments, HP offers Proactive Care or Critical Advantage. These services help deliver high levels of application availability through proactive service management and advanced technical response
You can get the support you need by choosing from one of a number of service packaged solutions we have designed to address wider set of customer support needs.
HP Technology Services meets business challenges with services offered in three support recommendations –Optimized Care, Standard Care, and Basic Care – available for each product group. Such support solutions enable customers to optimize technology operations, minimize risk and drive better business outcomes with easy-to-buy, easy-to-use scalable support recommendations for servers, storage, networking and software designed to meet your specific needs.
All three service recommendations include support services from the broader portfolio of Foundation Care and Proactive Care services.
Optimized Care
Optimized Care: Supports maintaining servers at optimum performance availability
HP ProLiant Server Hardware Installation
Provides for the basic hardware installation of HP branded servers, storage devices and networking options to assist you in bringing your new hardware into operation in a timely and professional mannerhttp://h20195.www2.hp.com/V2/GetPDF.aspx/5981-9356EN.pdf
HP Installation and Startup for Insight Control Software / HP SIM
Provides for the deployment and basic configuration of HP Insight Control or HP SIM (Systems Insight Manager) on HP ProLiant ML and DL series servers or HP BladeSystem servershttp://h20195.www2.hp.com/v2/GetPDF.aspx/4AA0-9972ENW.pdf
۳-Year HP 24×7 4 hour Response, Proactive Care Helps optimize your systems and delivers high levels of application availability through proactive service management and advanced technical response. A skilled Technical Manager will own your call and end to end until resolved, delivering a single point of contact for you. Helping you to resolve your hardware and software issues and minimizing downtime in your business critical environment.
Standard Care: Service recommendation that maintains high level of server availability
HP ProLiant Server Hardware Installation
Provides for the basic hardware installation of HP branded servers, storage devices and networking options to assist you in bringing your new hardware into operation in a timely and professional mannerhttp://h20195.www2.hp.com/V2/GetPDF.aspx/5981-9356EN.pdf
HP Installation and Startup for Insight Control Software / HP SIM
Provides for the deployment and basic configuration of HP Insight Control or HP SIM (Systems Insight Manager) on HP ProLiant ML and DL series servers or HP BladeSystem servershttp://h20195.www2.hp.com/v2/GetPDF.aspx/4AA0-9972ENW.pdf
۳-Year HP 24×7 4 hour Response, Collaborative Support
Provides problem resolution support across the stack of HW, firmware, and HP and 3rd party SW. In case the issue is with 3rd party SW, HP does known issue resolution. If HP cannot solve the issue, it will contact the third-party vendor and create a problem incident on your behalf. http://h20195.www2.hp.com/V2/GetPDF.aspx/4AA3-8232ENW.pdf
Additional Services: Software support service with 24X7 availability with a 2 hour response, Training courses on Microsoft, Linux (Red Hat and SUSE), VMware, and HP Insight Software, 10 Proactive Select Credit package, Factory Express http://www8.hp.com/us/en/business-services/it-services.html?compURI=1078865
Basic Care
Basic Care: delivers minimum recommended support service level
HP ProLiant Server Hardware Installation
Provides for the basic hardware installation of HP branded servers, storage devices and networking options to assist you in bringing your new hardware into operation in a timely and professional mannerhttp://h20195.www2.hp.com/V2/GetPDF.aspx/5981-9356EN.pdf
۳-Year HP 24×7 4 hour Response, Hardware Support Onsite Service
Provides you with rapid remote support and if required an HP authorized technical engineer will be on site 24X7 begin hardware maintenance service within 4 hours of the service request being logged http://h20195.www2.hp.com/V2/GetPDF.aspx/5982-6547EEE.pdf
۳-Year , HP 24×7 Software Support for Insight Control
Provides remote 3-year software support service that delivers comprehensive software services, including access to HP technical resources and software updates http://h20195.www2.hp.com/V2/GetPDF.aspx/5981-6645EEE.pdf
Personalized online support portal with access to information, tools and experts to support HP business products. Submit support cases online, chat with HP experts, access support resources or collaborate with peers. Learn morehttp://www.hp.com/go/hpsc
HP’s Support Center Mobile App * allows you to resolve issues yourself or quickly connect to an agent for live support. Now, you can get access to personalized IT support anywhere, anytime.
HP Insight Remote Support and HP Support Center are available at no additional cost with a HP warranty, HP Care Pack or HP contractual support agreement.
*HP’ Support Center Mobile App is subject to local availability
Warranty / Service Coverage
For ProLiant servers and storage systems, the services cover HP-branded hardware options qualified for the server, purchased at the same time or afterward, internal to the enclosure, as well as external monitors up to 22″ and tower UPS products; these items will be covered at the same service level and for the same coverage period as the server unless the maximum supported lifetime and/or the maximum usage limitation has been exceeded. Coverage of the UPS battery is not included; standard warranty terms and conditions apply.
The defective media retention service feature option applies only to Disk or eligible SSD/Flash Drives replaced by HP due to malfunction. It does not apply to any exchange of Disk or SSD/Flash Drives that have not failed. SSD/Flash Drives that are specified by HP as consumable parts and/or that have exceeded maximum supported lifetime and/or the maximum usage limit as set forth in the manufacturer’s operating manual or the technical data sheet are not eligible for the defective media retention service feature option.
For more information
To learn more on HP ProLiant servers and HP BladeSystem servers, please contact your HP sales representative or HP Authorized Channel Partner. Or visit: http://www.hp.com/services/proliant
NOTE: For the Standard Features shipped in the “Factory Integrated Models”, please see the “Configuration Information – Factory Integrated Models” section. NOTE: Pre-configured models ship with the configurations below. Options can be selected from the Core or Additional options section of this QuickSpecs. NOTE: HP does not allow factory integration of options into pre-configured models. Any additional options purchased will be shipped separately. NOTE: If you desire a custom configuration please see “Configuration Information – Factory Integrated Models” section of this QuickSpecs. NOTE: Maximum speed supported depends on the CPU installed. Entry model will support maximum speed of 1600 MHz.
Please see Memory Population Table or the Online Memory Configuration Tool at: www.hp.com/go/ddr3memory-configurator. NOTE: All Pre-configured Models come populated with some hard drive blanks installed. Should the customer need additional hard drive blanks, they can order more using either P/N 666987-B21: HP SFF Gen8 Hard Drive Blank Kit or P/N 666986-B21: HP LFF Gen8 Hard Drive Blank Kit. NOTE: Not all models are available in all regions. Check with your local country HP offices for availability.
Entry Models
HP ProLiant DL320e Gen8 G2120 1P 2GB-U Non-hot Plug SATA 4 LFF 350W PS Server
۶۷۵۴۲۰-xx1
Configuration Information – Factory Integrated Models
NOTE: This section lists some of the steps required to configure a Factory Integrated Model. To ensure only valid configurations are ordered, HP recommends the use of an HP approved configurator. Contact your local sales representative for information on configurable product offerings and requirements. NOTE: Factory Integrated Models must start with a CTO Server. NOTE: FIO indicates that this option is only available as a factory installable option. NOTE: All Factory Integrated Models will be populated with sufficient hard drive blanks based on the number of initial hard drives ordered with the server.
Step 1: Base Configuration (choose one of the following configurable models)
HP Models
HP ProLiant DL320e Gen8 Hot Plug 4 LFF Configure-to-order Server NOTE: All 6G SATA/SAS Drives listed in HDD section are tested and supported for both 3G and 6G speed. A HP Smart Array Controller is required for 6G HDD.
۶۷۵۵۹۷-B21
Factory Integrated Model ships with:
۱U Chassis with 4 LFF Hot Plug Drive Cage
HP Ethernet 1Gb 2-port 330i Adapter
HP iLO Management Engine (standard)
HP Dynamic Smart Array B120i SATA Controller (RAID 0/1/10) NOTE: For set up instructions for HP Dynamic Smart Array B120i SATA Controller please refer to the HP ProLiant DL300 series server user guide NOTE: For general information about HP Dynamic Smart Array B120i SATA Controller, please visit: http://h18004.www1.hp.com/products/servers/proliantstorage/arraycontrollers/
smartarrayb120i/index.html
HP ProLiant DL320e Gen8 Hot Plug 8 SFF Configure-to-order Server
۶۷۵۵۹۸-B21
Factory Integrated Model ships with:
۱U Chassis with 8 SFF Hot Plug Drive Cage
HP Ethernet 1Gb 2-port 330i Adapter
HP iLO Management Engine (standard)
HP Dynamic Smart Array B120i SATA Controller (RAID 0/1/10) NOTE: For set up instructions for HP Dynamic Smart Array B120i SATA Controller please refer to the HP ProLiant DL300 series server user guide NOTE: For general information about HP Dynamic Smart Array B120i SATA Controller, please visit: http://h18004.www1.hp.com/products/servers/proliantstorage/arraycontrollers/
smartarrayb120i/index.html
HP ProLiant DL320e Gen8 Non-hot Plug 4 LFF Configure-to-order Server NOTE: All 6G SATA/SAS Drives listed in HDD section are tested and supported for both 3G and 6G speed. A HP Smart Array Controller is required for 6G HDD.
۶۷۵۵۹۶-B21
Factory Integrated Model ships with:
۱U Chassis with 4 LFF Non hot plug Drive Cage
HP Ethernet 1Gb 2-port 330i Adapter
HP iLO Management Engine (standard)
HP Dynamic Smart Array B120i SATA Controller (RAID 0/1/10) NOTE: For set up instructions for HP Dynamic Smart Array B120i SATA Controller please refer to the HP ProLiant DL300 series server user guide NOTE: For general information about HP Dynamic Smart Array B120i SATA Controller, please visit: http://h18004.www1.hp.com/products/servers/proliantstorage/arraycontrollers/
smartarrayb120i/index.html
Step 2: Choose Required Options (only one of the following from each list unless otherwise noted)
HP Processors
Entry Processors NOTE: All support up to1600MHz DDR3 memory speeds.
HP DL320e Gen8 Intel® Pentium® G2120 (3.1GHz/2-core/3MB/55W) FIO Processor Kit
۷۰۳۲۷۸-L21
HP DL320e Gen8 Intel® Pentium® G2100T (2.6GHz/2-core/3MB/35W) FIO Processor Kit
۷۰۳۲۸۰-L21
Base Processors NOTE: All support up to1600MHz DDR3 memory speeds.
HP DL320e Gen8 Intel® Core™ i3-3220T (2.8GHz/2-core/3MB/35W) FIO Processor Kit
۷۰۰۷۹۲-L21
HP DL320e Gen8 Intel® Core™ i3-3240 (3.4GHz/2-core/3MB/55W) FIO Processor Kit
۷۰۰۷۸۶-L21
Performance Processors NOTE: All support up to 1600MHz DDR3 memory speeds.
HP DL320e Gen8 Intel® Xeon® E3-1220Lv2 (2.3GHz/2-core/3MB/17W) FIO Processor Kit
۶۸۲۷۸۹-L21
HP DL320e Gen8 Intel® Xeon® E3-1220v2 (3.1GHz/4-core/8MB/69W) FIO Processor Kit
۶۸۲۷۸۷-L21
HP DL320e Gen8 Intel® Xeon® E3-1230v2 (3.3GHz/4-core/8MB/69W) FIO Processor Kit
۶۸۲۷۸۵-L21
HP DL320e Gen8 Intel® Xeon® E3-1240v2 (3.4GHz/4-core/8MB/69W) FIO Processor Kit
۶۸۲۷۸۳-L21
HP DL320e Gen8 Intel® Xeon® E3-1270v2 (3.5GHz/4-core/8MB/69W) FIO Processor Kit
۶۸۲۷۸۱-L21
HP DL320e Gen8 Intel® Xeon® E3-1290v2 (3.7GHz/4-core/8MB/87W) FIO Processor Kit
۶۸۲۷۷۷-L21
HP Memory
NOTE: To realize the performance memory capabilities listed in this document, HP SmartMemory is required. For additional information, please see the HP SmartMemory QuickSpecs at:http://h18000.www1.hp.com/products/quickspecs/14225_div/14225_div.html (Worldwide) NOTE: HP memory from previous generation servers are not fully compatible with new Active Health features on the DL320e Gen8 Server.
Unbuffered with ECC DIMMs (UDIMMs)
HP 2GB (1x2GB) Single Rank x8 PC3-12800E (DDR3-1600) Unbuffered CAS-11 Memory Kit
۶۶۹۳۲۰-B21
HP 2GB (1x2GB) Single Rank x8 PC3L-10600E (DDR3-1333) Unbuffered CAS-9 Low Voltage Memory Kit
HP 8GB (1x8GB) Dual Rank x8 PC3L-10600E (DDR3-1333) Unbuffered CAS-9 Low Voltage Memory Kit
۶۴۷۹۰۹-B21
NOTE: All DDR3 memory option kits consist of one DIMM per kit. For detailed memory configuration rules and guidelines, please use the Online DDR3 Memory Configuration Tool: www.hp.com/go/ddr3memory-configurator. NOTE: Depending on the memory configuration and processor model, 1600MHz and 1333MHz memory may operate at a lower speed. Please see the see the “Memory” section later in this document and the Online Memory Configuration Tool for details atwww.hp.com/go/ddr3memory-configurator. NOTE: For additional memory rules and guidelines, see the “Memory” section later in this document. NOTE: For more information on ProLiant Energy Efficient Features, see:www.hp.com/go/proliant-energy-efficient NOTE: PC3L is a low voltage memory.
HP Power Supplies
NOTE: Prior to making a power supply selection it is highly recommended that the HP Power Advisor is run to determine the right size power supply for your server configuration. The HP Power Advisor is located at: www.hp.com/go/hppoweradvisor.
HP 350W 1U Factory Integrated Power Supply Kit NOTE: The 350 Watts Power Supply is rated at 85% efficiency.
۶۷۵۴۵۰-B21
HP Common Slot Platinum Plus Power Supply Kits NOTE: The following Power Supplies offer 94% efficiency with support for Intelligent Power Discovery.
HP 460W Common Slot Platinum Plus Hot Plug Power Supply Kit
۶۵۶۳۶۲-B21
HP Common Slot Gold Power Supplies NOTE: The following Power Supplies offer 92% efficiency.
HP 460W Common Slot Gold Hot Plug Power Supply Kit
۵۰۳۲۹۶-B21
HP DL320e Gen8 Factory Integrated RPS Enablement Kit NOTE: When selecting Common Slot power supply options for the DL320e Gen8 server, a HP DL320e Gen8 RPS Enablement FIO Kit (675451-B21) is required for HP common slot redundant power supply configurations.
۶۷۵۴۵۱-B21
NOTE: Option Kits for AC power supplies include the power supply and one PDU IEC cable. NOTE: HP ProLiant servers ship with an IEC-IEC power cord used for rack mounting with Power Distribution Units (PDUs). For a full list of optional HP power cords please go to www.hp.com/products/powercords
NOTE: Gen8 rail kits have changed significantly from prior generation rail kits. Please take a moment to review the installation documentation that comes with the server to help you with the installation of your Gen8 server. NOTE: Rail kits are optional for Gen8 and are no longer included standard with the server. Customers have the option to purchase their server without a rail kit. CAUTION: HP recommends that at least two people are used for all rack server installations. Please refer to your installation instructions for proper tools and number of people to use for any installation.
HP 1U FIO Friction Rail Kit NOTE: Kit contains non-telescoping friction rails which do not allow for in rack serviceability. The HP 1U Gen8 Cable Management Arm is not available when using Friction Rails. Caution: HP recommends that a minimum of two people is required for all Rack Server installations. Please refer to your installation instructions for proper tools and number of people to use for any installation.
۶۶۳۲۰۰-B21
HP Insight Software
HP Insight Control including 1yr 24×7 Support ProLiant ML/DL/BL-bundle Single Server FIO License
C6N36A
Converged Infrastructure Management Software
HP OneView with iLO Advanced – Server hardware required on same purchase order
NOTE: Some options may not be integrated at the factory. To ensure only valid configurations are ordered, HP recommends the use of an HP approved configurator. Contact your local sales representative for additional information.
HP Unique Options
HP DL320e Gen8 Mini SAS Cable Kit NOTE: HP DL320e Gen8 mini SAS cable kit would be required for the server to be compatible with 4LFF Hot Plug drives, H222 and P222 controllers.
۶۸۵۰۱۸-B21
HP Memory
NOTE: To realize the performance memory capabilities listed in this document, HP SmartMemory is required. For additional information, please see the HP SmartMemory QuickSpecs at:http://h18000.www1.hp.com/products/quickspecs/14225_div/14225_div.html (Worldwide) NOTE: HP memory from previous generation servers are not fully compatible with SmartMemory features in Gen8 Servers.
Unbuffered with ECC DIMMs (UDIMMs)
HP 2GB (1x2GB) Single Rank x8 PC3-12800E (DDR3-1600) Unbuffered CAS-11 Memory Kit
۶۶۹۳۲۰-B21
HP 2GB (1x2GB) Single Rank x8 PC3L-10600E (DDR3-1333) Unbuffered CAS-9 Low Voltage Memory Kit
HP 8GB (1x8GB) Dual Rank x8 PC3L-10600E (DDR3-1333) Unbuffered CAS-9 Low Voltage Memory Kit
۶۴۷۹۰۹-B21
NOTE: All DDR3 memory option kits consist of one DIMM per kit. For detailed memory configuration rules and guidelines, please use the Online DDR3 Memory Configuration Tool: www.hp.com/go/ddr3memory-configurator. NOTE: Kits described as LP include Low Power DIMMs. For more information on ProLiant Energy Efficient Features, see: www.hp.com/go/proliant-energy-efficient. NOTE: PC3L is a low voltage memory.
HP Optical Drives
HP 9.5mm SATA DVD-ROM JackBlack Optical Drive
۶۵۲۲۳۸-B21
HP 9.5mm SATA DVD-RW JackBlack Optical Drive
۶۵۲۲۴۱-B21
HP Hard Drives
NOTE: The components of a storage subsystem (e.g. the drive, the HBA/controller, firmware, and the server backplane) should operate at the same data transfer rate or the system bandwidth will be negotiated down to an acceptable level for all components. NOTE: Hard drives have either a one year or three year warranty; refer to the specific hard drive QuickSpecs for details.
SAS Hot Plug with SmartDrive SFF (2.5-inch) Enterprise Drives
HP 1.2TB 6G SAS 10K rpm SFF (2.5-inch) SC Enterprise 3yr Warranty Hard Drive
۶۹۷۵۷۴-B21
HP 900GB 6G SAS 10K rpm SFF (2.5-inch) SC Enterprise 3yr Warranty Hard Drive
۶۵۲۵۸۹-B21
HP 600GB 6G SAS 10K rpm SFF (2.5-inch) SC Enterprise 3yr Warranty Hard Drive
۶۵۲۵۸۳-B21
HP 450GB 6G SAS 10K rpm SFF (2.5-inch) SC Enterprise 3yr Warranty Hard Drive
۶۵۲۵۷۲-B21
HP 300GB 6G SAS 10K rpm SFF (2.5-inch) SC Enterprise 3yr Warranty Hard Drive
۶۵۲۵۶۴-B21
HP 300GB 6G SAS 15K rpm SFF (2.5-inch) SC Enterprise 3yr Warranty Hard Drive
۶۵۲۶۱۱-B21
HP 146GB 6G SAS 15K rpm SFF (2.5-inch) SC Enterprise 3yr Warranty Hard Drive
۶۵۲۶۰۵-B21
SAS Hot Plug SmartDrive SFF (2.5-inch) Midline Drives
HP 1TB 6G SAS 7.2K rpm SFF (2.5-inch) SC Midline 1yr Warranty Hard Drive
۶۵۲۷۴۹-B21
HP 500GB 6G SAS 7.2K rpm SFF (2.5-inch) SC Midline 1yr Warranty Hard Drive
۶۵۲۷۴۵-B21
SAS Hot Plug SmartDrive LFF (3.5-inch) Enterprise Drives
HP 600GB 6G SAS 15K rpm LFF (3.5-inch) SC Enterprise 3yr Warranty Hard Drive
۶۵۲۶۲۰-B21
HP 450GB 6G SAS 15K rpm LFF (3.5-inch) SC Enterprise 3yr Warranty Hard Drive
۶۵۲۶۱۵-B21
SAS Hot Plug SmartDrive LFF (3.5-inch) Midline Drives
HP 4TB 6G SAS 7.2K rpm LFF (3.5-inch) SC Midline 1yr Warranty Hard Drive
۶۹۵۵۱۰-B21
HP 3TB 6G SAS 7.2K rpm LFF (3.5-inch) SC Midline 1yr Warranty Hard Drive
۶۵۲۷۶۶-B21
HP 2TB 6G SAS 7.2K rpm LFF (3.5-inch) SC Midline 1yr Warranty Hard Drive
۶۵۲۷۵۷-B21
HP 1TB 6G SAS 7.2K rpm LFF (3.5-inch) SC Midline 1yr Warranty Hard Drive
۶۵۲۷۵۳-B21
SAS Non-Hot Plug LFF (3.5-inch) Enterprise (ENT) Drives
HP 600GB 6G SAS 15K rpm LFF (3.5-inch) Non-hot Plug Dual Port Enterprise 3yr Warranty Hard Drive
۵۱۶۸۳۰-B21
HP 450GB 6G SAS 15K rpm LFF (3.5-inch) Non-hot Plug Dual Port Enterprise 3yr Warranty Hard Drive
Hard Drive Kits NOTE: All Factory Integrated Models will be populated with sufficient hard drive blanks based on the number of initial hard drives ordered with the server. NOTE: The part numbers for single HDD blanks below are provided should the customer require replacement HDD blanks for their server. NOTE: The mixing of standard SAS drives with SAS SSD drives is supported within the server, but limits the RAID configuration to two separate RAID 0 volumes. Mixing of other drives types is not supported.
HP LFF Gen8 Hard Drive Blank Kit
۶۶۶۹۸۶-B21
HP SFF Gen8 Hard Drive Blank Kit
۶۶۶۹۸۷-B21
HP Networking
Gigabit Ethernet Adapters
HP NC112T PCI Express Gigabit Server Adapter
۵۰۳۷۴۶-B21
HP NC365T 4-port Ethernet Server Adapter
۵۹۳۷۲۲-B21
HP Ethernet 1Gb 2-port 361T Adapter
۶۵۲۴۹۷-B21
HP Ethernet 1Gb 4-port 331T Adapter
۶۴۷۵۹۴-B21
HP Ethernet 1Gb 2-port 332T Adapter
۶۱۵۷۳۲-B21
۱۰ Gigabit Ethernet Adapters NOTE: A minimum of two Gigabytes (2 GB) of server memory is required per each adapter.
HP NC523SFP 10Gb 2-port Server Adapter
۵۹۳۷۱۷-B21
HP NC552SFP 10Gb 2-port Ethernet Server Adapter
۶۱۴۲۰۳-B21
HP Ethernet 10Gb 2-port 530T Adapter
۶۵۶۵۹۶-B21
HP Ethernet 10Gb 2-port 560SFP+ Adapter
۶۶۵۲۴۹-B21
NOTE: Please see the QuickSpecs for Technical Specifications and additional information: www.hp.com/go/ProLiantNICs.
HP Power Supplies
NOTE: Prior to making a power supply selection it is highly recommended that the HP Power Advisor is run to determine the right size power supply for your server configuration. The HP Power Advisor is located at: www.hp.com/go/hppoweradvisor
HP Common Slot Platinum Plus Power Supply Kits NOTE: The following Power Supplies offer 94% efficiency with support for Intelligent Power Discovery.
HP 460W Common Slot Platinum Plus Hot Plug Power Supply Kit
۶۵۶۳۶۲-B21
HP Common Slot Gold Power Supplies NOTE: The following Power Supplies offer 92% efficiency.
HP 460W Common Slot Gold Hot Plug Power Supply Kit
۵۰۳۲۹۶-B21
NOTE: Option Kits for AC power supplies include the power supply and one PDU IEC cable. NOTE: HP ProLiant servers ship with an IEC-IEC power cord used for rack mounting with Power Distribution Units (PDUs). For a full list of optional HP power cords please go to www.hp.com/products/powercords
NOTE: Some options may not be integrated at the factory. To ensure only valid configurations are ordered, HP recommends the use of an HP approved configurator. Contact your local sales representative for additional information.
HP Management Hardware
HP Dedicated iLO Management Port Kit
۶۷۴۸۴۵-B21
HP Insight Software
HP Insight Control
HP Insight Control including 1yr 24×7 Technical Support and Updates Single Server License
C6N27A
HP Insight Control including 1yr 24×7 Technical Support and Updates Electronic License
C6N28ABE
HP Insight Control Server Provisioning Media Kit
BD883A
HP Insight Management Media Kit
C6N31A
HP Insight Control including 1yr 24×7 Support ProLiant ML/DL/BL-bundle FIO Electronic License
C6N36ABE
HP Insight Control Server Deployment including 1yr 24×7 Support Electronic License
T9082AAE
HP Insight Control Server Deployment including 1yr 24×7 Support Single Server License
۴۵۲۱۵۱-B21
NOTE: Electronic and Flexible-Quantity licenses can be used to purchase multiple licenses with a single activation key. NOTE: Customer will receive a license entitlement certificate. The license entitlement certificate must be redeemed online or via fax in order to obtain the license activation key(s). Includes one year of 24 x 7 HP Software Technical Support and Update Service. NOTE: Licenses ship without media. The HP Insight Control Media Kit can be ordered separately, or can be downloaded at: http://www.hp.com/go/insightupdates.
HP Insight Cluster Management Utility 1yr 24×7 Flexible License
QL803B
HP Insight Cluster Management Utility 3yr 24×7 Flexible License NOTE: These part numbers can be used to purchase one certificate for multiple licenses and support with a single activation key. Each license is for one node (server). Customer will receive a printed end user license agreement and license entitlement certificate via physical shipment. The license entitlement certificate must be redeemed online in order to obtain a license key. Customer also will receive a support agreement.
NOTE: The TPM (Trusted Platform Module) is a microcontroller chip that can securely store artifacts used to authenticate the server platform. These artifacts can include passwords, certificates and encryption keys. Windows® BitLockerâ„¢ Drive Encryption (BitLocker) is a data protection feature available in Windows Server® ۲۰۰۸٫ BitLocker leverages the enhanced security capabilities of a Trusted Platform Module (TPM) version 1.2. The TPM works with BitLocker to help protect user data and to ensure that a server running Windows Server 2008 has not been tampered with while the system was offline. For more information about TPM, including a white paper, go to: www.hp.com/go/TPM. NOTE: ProLiant OS pre-installed units will come with the partition required for TPM deployment. NOTE: The TPM key is unique to every TPM deployed server and must be retained. Misplacing or losing the key could result in data loss.
HP 1U Security Gen8 Bezel Kit
۶۶۴۹۱۸-B21
HP Storage Controllers
SAS Controllers
Smart Array P222 Controller
HP Smart Array P222/512 FBWC 6Gb 1-port Int/1-port Ext SAS Controller
۶۳۱۶۶۷-B21
Smart Array P420 Controller
HP Smart Array P420/1GB FBWC 6Gb 2-ports Int SAS Controller
۶۳۱۶۷۰-B21
HP Smart Array P420/2GB FBWC 6Gb 2-ports Int SAS Controller
۶۳۱۶۷۱-B21
Smart Array P421 Controller
HP Smart Array P421/1GB FBWC 6Gb 2-ports Ext SAS Controller
۶۳۱۶۷۳-B21
HP Smart Array P421/2GB FBWC 6Gb 2-ports Ext SAS Controller
۶۳۱۶۷۴-B21
Optional Upgrades
HP 2GB P-series Smart Array Flash Backed Write Cache
NOTE: For the complete range of tape drives, autoloaders, libraries and media see:http://www.hp.com/go/tape. For hardware and software compatibility of HP tape backup products see: http://www.hp.com/storage/SPOCK and www.hp.com/go/ebs. NOTE: For Internal drives to be connected to DL servers please make sure that you order rack mount kit as well.
HP StoreEver LTO-6 Ultrium 6250 Tape Drive in 1U Rack-mount Kit
C0L99A
HP StoreEver LTO-6 Ultrium 6650 Internal Tape Drive
EH963A
HP StoreEver LTO-6 Ultrium 6650 External Tape Drive
EH964A
HP StoreEver LTO-6 Ultrium 6250 Internal Tape Drive
EH969A
HP StoreEver LTO-6 Ultrium 6250 External Tape Drive
NOTE: For additional information on HP Uninterruptible Power Systems please go to:www.hp.com/servers/rackups.
NOTE: For additional information on sizing your HP UPS, please reference:http://www.upssizer.com NOTE: Please see the UPS and PDU cable matrix’s on the HP Power Protection and Management page. Under Power Cords, click on the “HP Power Cord Matrix” link. That link will list cable descriptions, requirements, and specifications for UPS and PDU units. Please see the following link: www.hp.com/products/powercords.
HP Basic Power Distribution Units
HP 1.9kVA 120 Volt 12 Outlet NA/JP Basic Power Distribution Unit
H5M54A
HP 2.8kVA 120 Volt 18 Outlet NA/JP Basic Power Distribution Unit
H5M55A
HP 3.6kVA 200-240 Volt 12 Outlet WW Basic Power Distribution Unit
H5M56A
HP 3.6kVA 200-240 Volt 20 Outlet WW Basic Power Distribution Unit
H5M57A
HP 4.9kVA 208 Volt 20 Outlet NA/JP Basic Power Distribution Unit
H5M58A
HP 4.9kVA 208 Volt 30 Outlet NA/JP Basic Power Distribution Unit
H5M59A
HP 8.3kVA 208 Volt 36 Outlet NA/JP Basic Power Distribution Unit
H5M60A
HP 8.6kVA 208 Volt Three Phase 18 Outlet NA/JP Basic Power Distribution Unit
H5M61A
HP 8.6kVA 208 Volt Three Phase 30 Outlet NA/JP Basic Power Distribution Unit
H5M62A
HP 5.7kVA 208 Volt Three Phase 27 Outlet NA/JP Dual Voltage Basic Power Distribution Unit
H5M63A
HP 8.6kVA 208 Volt Three Phase 30 Outlet NA/JP Dual Voltage Basic Power Distribution Unit
H5M64A
HP 11kVA 400 Volt Three Phase 42 Outlet NA Basic Power Distribution Unit
H5M67A
HP 7.3kVA 230 Volt 20 Outlet INTL Basic Power Distribution Unit
H5M68A
HP 7.3kVA 230 Volt 30 Outlet INTL Basic Power Distribution Unit
H5M70A
HP 11kVA 230 Volt 36 Outlet INTL Basic Power Distribution Unit
H5M71A
HP 11kVA 400 Volt Three Phase 30 Outlet INTL Basic Power Distribution Unit
H5M72A
HP 11kVA 400 Volt Three Phase 42 Outlet INTL Basic Power Distribution Unit
H5M73A
HP Hardwired 200-240 Volt 36 Outlet WW Basic Power Distribution Unit
H5M75A
HP 13.2kVA 480 Volt Three Phase 15 Outlet NA Basic Power Distribution Unit
H3X07A
HP 19.9kVA 480 Volt Three Phase 30 Outlet NA Basic Power Distribution Unit
H3X08A
HP 277 Volt options for H3X07A and H3X08A
HP 800VA – 277V Input / 230V Output NA Rack Mount Transformer
NOTE: Additional HP Power Distribution Units are available. For a complete list of all HP PDUs and additional information please visit www.hp.com/go/rackandpower.
HP Remote Monitoring Power Distribution Units
HP 2.8kVA 120 Volt 12 Outlet NA/JP Monitored Power Distribution Unit
D9N43A
HP 4.9kVA 208 Volt 12 Outlet NA/JP Monitored Power Distribution Unit
D9N44A
HP 3.6kVA 200-240 Volt 16 Outlet WW Monitored Power Distribution Unit
D9N45A
HP 3.6kVA 200-240 Volt 12 Outlet WW Monitored Power Distribution Unit
D9N46A
HP 4.9kVA 208 Volt 24 Outlet NA/JP Monitored Power Distribution Unit
D9N47A
HP 7.3kVA 230 Volt 24 Outlet INTL Monitored Power Distribution Unit
D9N48A
HP 8.3kVA 208 Volt 33 Outlet NA Monitored Power Distribution Unit
D9N49A
HP 7.3kVA 230 Volt 36 Outlet INTL Monitored Power Distribution Unit
D9N50A
HP 8.6kVA 208 Volt Three Phase 21 Outlet NA/JP Monitored Power Distribution Unit
D9N51A
HP 5.7kVA 208 Volt Three Phase 21 Outlet NA/JP Dual Voltage Monitored Power Distribution Unit
D9N52A
HP 8.6kVA 208 Volt Three Phase 24 Outlet NA/JP Dual Voltage Monitored Power Distribution Unit
D9N53A
HP 17.3kVA 208 Volt Three Phase 27 Outlet NA/JP Monitored Power Distribution Unit
D9N54A
HP 11kVA 400 Volt Three Phase 21 Outlet INTL Monitored Power Distribution Unit
D9N55A
HP 22kVA 400 Volt Three Phase 33 Outlet INTL Monitored Power Distribution Unit
D9N56A
HP 11kVA 400 Volt Three Phase 33 Outlet INTL Monitored Power Distribution Unit
D9N57A
HP 14.4kVA 208 Volt Three Phase 24 Outlet NA Monitored Power Distribution Unit
D9N58A
HP 17.3kVA 208 Volt Three Phase 24 Outlet NA/JP Monitored Power Distribution Unit
D9N59A
HP 22kVA 400 Volt Three Phase 24 Outlet INTL Monitored Power Distribution Unit
D9N60A
HP 16.6kVA 400 Volt Three Phase 33 Outlet NA Monitored Power Distribution Unit
D9N61A
HP 16.6kVA 400 Volt Three Phase 24 Outlet NA Monitored Power Distribution Unit
D9N62A
HP 19.9kVA 480 Volt Three Phase 30 Outlet NA Monitored Power Distribution Unit
NOTE: For additional information on HP Power Distribution Units including accessories please go to: www.hp.com/go/pdu.
NOTE: Please see the UPS and PDU cable matrix’s on the HP Power Protection and Management page. Under Power Cords, click on the “HP Power Cord Matrix” link. That link will list cable descriptions, requirements, and specifications for UPS and PDU units. Please see the following link: www.hp.com/products/powercords. NOTE: This PDU has a detachable input power cord and allows for adaptability to country specific power requirements.
HP 1U Cable Management Arm for Ball Bearing Gen8 Rail Kit
۶۶۳۲۰۳-B21
HP 1U Small Form Factor Ball Bearing Gen8 Rail Kit
۶۶۳۲۰۱-B21
HP 1U Large Form Factor Ball Bearing Gen8 Rail Kit
۶۶۳۲۰۲-B21
HP USB and SD Options
HP Flash Media Kits for USB Drives
HP 2GB USB Flash Media Drive Key Kit
۶۰۸۴۴۷-B21
NOTE: HP qualified blank USB key for use with HP ProLiant servers that support the VMware virtualization environment and other HP value-add software. HP recommends this industry standard USB flash device for use with VMware ESXi. USB device must be installed in the internal slot of the ProLiant server for use with VMware ESXi. Refer to HP VMware Getting Started Guide for installation instructions.
HP 4GB SD Enterprise Performance Flash Media Kit
۵۸۰۳۸۷-B21
HP 4GB SD Enterprise Performance Flash Media Kit NOTE: Blank SD media device is supported for use with VMware and Citrix. SD media must be installed in the internal slot of the ProLiant server. Learn more at:http://www.hp.com/go/proliantvirtualization.
HP Enterprise Mainstream Flash Media Kits for Memory Cards
Proactive Care NOTE: Collaborative Support plus Proactive services delivered by the onshore, local language Advanced Solution Center (ASC), end-to-end case ownership from a Technical Solution Specialists and Technical Account Manager who remotely delivers firmware/software revision management, proactive scans and incident trend reports. Recommended for customers running a virtualized infrastructure and/or customers who desire an enhanced call support experience.
HP 3 year 4 hour 24×7 ProLiant DL320e Proactive Care Service
U6F03E
HP 3 year 4 hour 24×7 with Defective Media Retention ProLiant DL320e Proactive Care Service
U6F04E
HP 3 year 6 hour Call to Repair 24×7 ProLiant DL320e Proactive Care Service
U6F09E
HP 3 year 6 hour Call to Repair 24×7 w/Defective Media Retention ProLiant DL320e Proactive Care SVC
U6F10E
Collaborative Support NOTE: Hardware break/fix plus 24×7 software diagnosis support with collaborative call management for a broad spectrum of 3rd Party software products including O/S and hypervisors. Recommended for customers procuring 3rd party SW O/S and hypervisors from the software vendors directly and deploying them on HP ProLiant servers.
HP 3 year 4 hour 24×7 ProLiant DL320e Collaborative Support
U6F01E
HP 3 year 4 hour 24×7 with Defective Media Retention ProLiant DL320e Collaborative Support
U6F02E
HP 3 year 6 hour Call to Repair 24×7 ProLiant DL320e Collaborative Support
U6F07E
HP 3 year 6 hour Call to Repair 24×7 w/Defective Media Retention ProLiant DL320e Collaborative Sup
U6F08E
Proactive Care Personalized Support Option NOTE: To add an onsite Account Support Manager (ASM) to Proactive Care. ASM is an assigned resource who delivers support planning and brings technical expertise and best practices advices for the customer’s environment.
HP 3 year ISS ProactiveCare Personalized Support
U6W98E
Installation Services NOTE: Reduce the time required to get your system up and running and help minimize disruptions to your business.
New HP SmartMemory now provides additional protection for your servers. With HP Authentication it can verify that you have true HP Qualified Memory in your HP ProLiant Gen8 server. With HP SmartMemory your new HP ProLiant server can take advantage of additional Gen8 enhancements in performance, durability and future manageability support through HP Active Health System
Memory Subsystem Architecture
Intel Processor socket supports 2 channels and 2 DIMMs per channel. Total max. memory up to 32GB DDR3 PC3-12800E1600MHz.
Standard Memory Plus Optional Memory
Up to 32 GB memory is available with the optional installation of 4 x 8GB PC3-12800E UDIMM ECC DDR3 UDIMM Memory kits, operating at 1600MHz when fully populated at 2 DIMMs per Channel in 4 slots. NOTE: The below chart does not represent all possible memory configurations. NOTE: For best performance, it is recommended that customer installs memory in identical pairs
General Memory Population Rules and Guidelines:
The HP ProLiant DL320e Gen8 Server has four memory slots
There are two channels per server with two DIMM slot per channel
Memory channel A consists of the two (2) DIMMs that are closest to the processor
Memory channel B consists of the two (2) DIMMs that are furthest from the processor
Different types of processors have different types of memory support.
Support for single/dual-rank 1333/1600 MT/s ECC UDIMM (unbuffered DIMMS)
The server supports up to 32 GB (4 x 8-GB) for Unbuffered DIMMs
No support for LV-DIMMs; RDIMMs; Non-ECC UDIMMs
Do not install DIMMs if the processor is not installed
Populate DIMMs from heaviest load (double-rank) to lightest load (single-rank)
Always use HP qualified DIMM
Farthest DIMM (either CHA or CHB) should always be populated first
HP 8GB (1x8GB) Dual Rank x8 PC3L-10600E (DDR3-1333) Unbuffered CAS-9 Low Voltage Memory Kit
۶۴۷۹۰۹-B21
NOTE: All DDR3 memory option kits consist of one DIMM per kit. For detailed memory configuration rules and guidelines, please use the Online DDR3 Memory Configuration Tool: www.hp.com/go/ddr3memory-configurator. NOTE: Kits described as LP include Low Power DIMMs. For more information on ProLiant Energy Efficient Features, see: www.hp.com/go/proliant-energy-efficient. NOTE: PC3L is a low voltage memory.
۱٫۷ x 17.11 x 27.5 inches (4.32 x 43.46 x 69.90 cm)
۴ LFF
۱٫۷ x 17.11 x 29.5 inches (4.32 x 43.46 x 75.0 cm)
Weight (approximate)
Maximum
(all hard drives, power supply, and processor installed)
۸ SFF/4 LFF – 16.2/16.8 kg, 35.7/37.0 lb
Minimum
(one hard drive, power supply, and processor installed)
۸ SFF/4 LFF – 10.9/11.9 kg, 24.0/26.2 lb
Input Requirements
(HP ProLiant 350 W power supply)
Rated Line Voltage
۱۰۰ to 120 VAC
Rated Input Current
۶ Amps (at 100VAC) to 3 Amps (at 200 VAC)
Rated Input Frequency
۵۰ to 60 Hz
Power Supply Output
(per power supply)
Rated Steady-State Power
۳۵۰ W (at 100 to 120 VAC),
۳۵۰ W (at 200 to 240 VAC)
Maximum Peak Power
۴۰۰ W (at 100 to 120 VAC),
۴۰۰ W (at 200 to 240 VAC)
System Inlet Temperature
Operating
۱۰° to 35°C (50° to 95°F) at sea level with an altitude derating of 1.0°C per every 304.8 m (1.8°F per every 1000 ft) above sea level to a maximum of 3048 m (10,000 ft), no direct sustained sunlight. Maximum rate of change is 10°C/hr (18°F/hr). The upper limit may be limited by the type and number of options installed.
System performance may be reduced if operating with a fan fault or above 30°C (86°F).
Non-operating
-۳۰° to 60°C (-22° to 140°F). Maximum rate of change is 20°C/hr (36°F/hr).
Relative Humidity
(non-condensing)
Operating
۱۰ to 90% relative humidity (Rh), 28°C (82.4°F) maximum wet bulb temperature, non-condensing.
Non-operating
۵ to 95% relative humidity (Rh), 38.7°C (101.7°F) maximum wet bulb temperature, non-condensing.
Altitude
Operating
۳۰۴۸ m (10,000 ft). This value may be limited by the type and number of options installed. Maximum allowable altitude change rate is 457 m/min (1500 ft/min).
Non-operating
۹۱۴۴ m (30,000 ft). Maximum allowable altitude change rate is 457 m/min (1500 ft/min).
Acoustic Noise
Listed are the declared A-Weighted sound power levels (LWAd) and declared average bystander position A-Weighted sound pressure levels (LpAm) when the product is operating in a 23°C ambient environment. Noise emissions were measured in accordance with ISO 7779 (ECMA 74) and declared in accordance with ISO 9296 (ECMA 109).
Idle (Note 1)
LWAd
۵٫۰ B
LpAm
۳۵ dB Average Bystander
Operating
LWAd
۵٫۱ B
LpAm
۳۵ dB Average Bystander
NOTE: Values are subject to change without notification and are for reference only. NOTE: Performance of system, options, and ancillary equipment will vary depending on the system configuration. NOTE: Levels presented do not account for non-Hewlett-Packard installed hardware.
Emissions Classification (EMC)
FCC Rating
Class A
Normative Standards
CISPR 22; EN55022; EN55024; FCC CFR 47, Pt 15; ICES-003; CNS13438; GB9254; K22;K24; EN 61000-3-2; EN 61000-3-3; EN 60950-1; IEC 60950-1
NOTE: Product conformance to cited product specifications is based on sample (type) testing, evaluation, or assessment. This product or family of products is eligible to bear the appropriate compliance logos and statements.
HP Dynamic Smart Array B120i Controller
Dimensions
Embedded
Disk Drive and Enclosure Interface – Transfer rate
Up to 6Gb/s SATA (Serial ATA)
Connectors
۶ internal SATA connectors
Server Interface
x4 PCIe 2.0
SATA Speed
۶Gb/s SATA links
Cache Memory
Zero Memory RAID has no cache memory
Logical Drives Supported
Up to 8 logical volumes (6 physical drives)
Host Memory Addressing
۶۴-bit, supporting greater than 4GB server memory space
Hewlett-Packard offers end-of-life HP product return, trade-in, and recycling programs in many geographic areas. For trade-in information, please go to:http://www.hp.com/go/green. To recycle your product, please go to:http://www.hp.com/go/green or contact your nearest HP sales office. Products returned to HP will be recycled, recovered or disposed of in a responsible manner.
The EU WEEE directive (2002/95/EC) requires manufacturers to provide treatment information for each product type for use by treatment facilities. This information (product disassembly instructions) is posted on the Hewlett Packard web site at:http://www.hp.com/go/green. These instructions may be used by recyclers and other WEEE treatment facilities as well as HP OEM customers who integrate and re-sell HP equipment.
